[phpBB Debug] PHP Warning: in file [ROOT]/ext/senky/relativedates/event/listener.php on line 100: Undefined array key "time"
[phpBB Debug] PHP Warning: in file [ROOT]/ext/senky/relativedates/event/listener.php on line 100: Undefined array key "time"
Raptor Chapter • New member from Devon
Page 1 of 1

New member from Devon

Posted: |April 23rd, 2019|, 4:32 am
by motojohn
Image
soon to be the new owner of this beast looking forward to it
Image

Re: New member from Devon

Posted: |April 23rd, 2019|, 7:42 am
by snapdragon
Oooh shiny ๐Ÿ˜€
Welcome to the forum :ride:

Re: New member from Devon

Posted: |April 23rd, 2019|, 2:37 pm
by shebee
Very nice... enjoy :revrev:

Re: New member from Devon

Posted: |April 23rd, 2019|, 5:02 pm
by nickst4
Welcome MJ!

I saw that one on ebay and thought the high exhausts (despite the extra pipery) balanced the droop-snoot rather well. Enjoy! :ride:

Nick

Re: New member from Devon

Posted: |April 23rd, 2019|, 5:44 pm
by motojohn
you are right about the pipes , they do look to high, but i think it is more to do with the camera angle i have not seen the bike in the flesh yet so time will tell , looking forward to playing with it

Re: New member from Devon

Posted: |April 24th, 2019|, 2:28 am
by Ayupwesty
Looks like itโ€™s been well looked after, very nice!

Re: New member from Devon

Posted: |May 1st, 2019|, 9:18 pm
by motojohn
picked up the bike last night , very fast and very loud , the rear shock is very soft and bouncy !! and the rear brake is next to useless , going o look a a shock replacement and mounting plates to rase the back end up a bit but nor sure how high to go as they start from 20mm to 35mm raise

Re: New member from Devon

Posted: |May 3rd, 2019|, 5:47 pm
by nickst4
MJ:

Be careful about shock replacement and raising the shock linkage. :nod:

If you opt for an adjustable shock such as the oft-mentioned Aprilia one (and I have two sitting in my shed awaiting a new owner since I got a Matris shock custom-made), you'll likely find that the commercially-available linkages don't allow room for the adjuster boss at the base of the shock. It's no big deal to make your own linkages though, given you can work with plate metal (mine are steel) and drill accurate holes.

Nick

Re: New member from Devon

Posted: |May 4th, 2019|, 5:37 pm
by andybaggies
and the rear brake is next to useless
Possibly just needs bleeding - they're a right faff to do. You need to remove the caliper off it's mounting plate and ensure it's above the height of the master cylinder. I've also had the master cylinder piston seize which either requires a good clean or replacing - not too expensive from what I recall. 30 sovs or so.
going o look a a shock replacement and mounting plates to rase the back end up a bit
After I replaced just the shock, which was like yours soft & gave a saggy rear end (oo er), the ride height improved noticeably and the handling to suit. I'm not sure it really benefits from raising.

The cheaper option, of course, is to lower the forks but beware the old slappers.. :shock:

Re: New member from Devon

Posted: |May 4th, 2019|, 5:42 pm
by andybaggies
In fact I've just noticed your fork sliders are gold... Are they the original forks or has a previous owner had them replated along with other internal mods perhaps?

The forks are known to be of basic ability and a couple of us have replaced the internals with fully adjustable catridges from Matris. They help a lot.

Give us time and we'll soon be emptying your bank with further suggestions :D